Leading 10 common forklift accidents ， forklift procedure need to pay attention to these issues ！.
Leading 10 common forklift accidents ， forklift procedure need to pay attention to these issues ！.
Blog Article
Don't ignore the forklift at work. If the procedure is bad, there will certainly be severe crashes in mins, and there are numerous accidents involving forklifts.
Case 1: The forklift freight obstructed the driver's sight, and the person in front can not be found, resulting in a rolling accident.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift raises the personnel illegally, the forklift driver does not wear the safety belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.
Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the tons is secure and reputable.
4. The start needs to be slow-moving and stable.
Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the job site or while driving, take care that there will be no challenges overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork ought to be decreased to the normal driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will certainly cause the car to lose side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique conditions.
6. When the forklift is running, it must obey the web traffic rules in the factory and should keep a specific security range from the automobile ahead. .
7. When the forklift is running, the tons has to be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised other than when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never operate with ailments or conceal them.
loading and dumping.
1. When fork-loading products, the distance in between the two forks need to be changed as needed to make the lots of the two forks well balanced and not manipulated, and one side of the item need to be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security warning signs need to be set up to advise bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other items or objects. The lots should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction Stand-on Electric Pallet Stacker of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining Electric Forklift Truck for Warehouse is prohibited, and it is forbidden to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.
Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should unload the goods or lower the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance needs to be examined, and gas, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the procedure of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leakage ought to also be inspected and the seals should be replaced in time.
Forklift Safety Operation Specifications.
1. You need to check prior to leaving the vehicle;.
2. When you run into somebody before you during driving, you should send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The turning must not be also sharp to prevent the propensity of " cost-free switching";.
6. Running up and down the slope must be slow-moving and uniform, and no turning on the incline is allowed.
7. Do not drive across the gradient. When the gradient is greater than 10%, the car needs to be driven backwards when declining;.
8. When the forklift personnel carry the goods and progress, if they encounter big or hefty items and most likely to the driver's line of vision, they need to take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not permitted to raise the goods for cross country driving.
3. It is not permitted to grab the goods by turning over the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and other hazardous chemicals with forks.
5. It is not permitted to utilize inertia force to pick up the goods.
6. It is not enabled to use stopping pressure to exile round or easy-to-roll things.
7. It is not permitted to bring people to work on the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive laterally on slopes
.
Car parking is not allowed under the list below problems.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the exact same length as the obstacle must be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844